b'Print on header/sleeve- A custom colored or printed felt header that isSide with Zipper- A tent side with a zipper that runs most of the height sewn on the left side of the pennant.The size depends on the size of theof the tent, about 8.The zipper allows for easy access to the rear of the pennant itself. Customer to specify the color or print on the header. tent.Print on plastic header- A 1 white plastic header with a thin nylon rope3 sided cut out- A table cover that cover the top and all 3 sides of the sewn into top of the header with a one color imprint.A simple designtable.The table cover will cover 2 on the backside of the table to help works best since the imprint area is small.The flags are sewn into thekeep the table cover in place.The sides are cut to size and hemmed.header with 2 rows of stitching.5 of extra header is left on each for easyOnce on the table this option gives the illusion of a fitted table cover but tying. allows for more flexibility in the table size and allows easy access to the underside of the table.Printed streamer- Custom printed streamer for standard windsocks.The print can be a design or text.The streamers will be digitally printed3 sided cut out withhook & loop tape- A table cover that covers so colors are not limited. the top and all 3 sides of the table.The table cover will cover 2 on the backside of the table to help keep the table cover in place.The sides Rectangle flag- Rectangle shaped flags for streamers.This is anare cut to size and finished with hoop & loop tape.Once on the table, alternative to the default pennant shaped flags. the sides of the table cover can be connected together via the hook and loop tape.This option gives the polished look of a fitted table cover but Reinforced bottom grommet- A grommet reinforced with a clearallows easy access to the underside of the table.plastic square.The plastic square reinforces the grommet and keeps the grommet from tearing out of the fabric.Reinforced bottom grommets3 sided draped- A table cover that covers the top and 3 sides of a table.are standard on feather, swooper and other advertising flags.TheseThe table cover will cover 2 on the backside of the table to help keep the grommets are used to secure the flag to the pole. table cover in place.The table cover is essentially a large rectangle; the extra material will drape neatly in the font corners.Reinforced printed sleeve- Any size: a custom sized 2-layer canvas sleeve affixed to the side of the flag.The inside layer of the sleeve is3 sided fitted- A table cover that covers the top and all 3 sides of the made of a heavy duty canvas for support and rigidity.The canvas is thentable.The sides are cut to size and sewn together, creating a more warped in a material that is printed to match the flag to create the 2ndstructured table cover.The table cover will cover 2 on the backside of layer.This sleeve is also finished with a leather tab for easy hanging.the table to help keep the table cover in place.Fitted table covers fit snuggly against the sides of the table.Scalloped valance- Event tents have a valance or overhang that is 12 tall and warps all the way around the tent.A scalloped valance has a4 sided cut out- A table cover that covers the top and all 4 sides of scalloped or wavy edge. the table.The sides are cut to size and hemmed.Once on the table, this option gives the illusion of a fitted table cover but allows for more Side with hook & loop tape- A tent side with an 8 slit in the middle. flexibility in the table size and allows easy access to the underside of the The slit is lined with hook & loop tape so it can be opened and closedtable.easily, giving easy access to the back side of the tent.Sleeve for motorcycle pole- 0.75 binding tape sleeve, open at both 4 sided cut out with hook & loop tape- A table cover that covers theends.The binding tape sleeve holds the flag upright on the pole and top and all 4 sides of the table.The sides are cut to size and finished withis strong enough to hold up under the strong winds experienced on a G P T I O N S L T Y R M I N O O O E hoop & loop tape.Once on the table, the sides of the table cover canmotorcycle.be connected together via the hook and loop tape.This option gives the polished look of a fitted table cover but allows easy access to the1.875" sleeve on left/1.25" sleeve on top- Finishing for the smaller underside of the table. standard tower poles: 6x22 and 9x22.The flag is finished with a 1.875 white canvas, open at both ends, sleeve sewn to the vertical side of the 4 sided draped- A table cover that covers the top and 4 sides of a table. flag and a 1.25 white canvas sleeve, open at both ends, sewn on top of The table cover is essentially a large rectangle; the extra material willthe flag.drape neatly in the corners.0.5" for extended car flag pole- 0.5" sleeve, closed on top.Will fit the 4 sided fitted- A table cover that covers the top and all 4 sides of the0.5" fiberglass pole on the extended car flag pole.Sleeves are measured table.The sides are cut to size and sewn together, creating a moreflat and fit a pole with a max diameter of approximately half the size of structured table cover.Fitted table covers fit snuggly against the sidesthe sleeve. Sleeve material should be chosen from the Sleeve/header of the table.material chart.4 sided fitted with back zipper- A table cover that covers the top and0.5 sleeve closed on top with snap clip- 0.5" flag material sleeve all 4 sides of the table.The sides are cut to size and sewn together,closed on top with a 1.5" aluminum snap hook attached to the bottom creating a more structured table cover.Fitted table covers fit snugglyof the sleeve.The sleeve is white by default but can be colored upon against the sides of the table.The back side of the table has a zipperrequest.running the height of the table.The zipper allows for easy access to the underside of the table.1" (sleeve) open at both ends- 1" sleeve, open at both ends.Sleeves are measured flat and fit a pole with a max diameter of approximately half 2" sleeve closed on top- 2 white canvas sleeve, closed on top.This isthe size of the sleeve. Sleeve material should be chosen from the Sleeve/the standard finishing for all sized teardrop poles.The sleeve runs theheader material chart.length of the flag and follows the curve of the top flag.2.25 sleeve on left/1.25 sleeve on top- Finishing for the larger 0.5 sleeve for bike flag - 0.5 sleeve, closed on top. The sleeve is madestandard tower poles: 12x28, 13x36 and 15x35.The flag is finished from the same material as the flag and is white by default.A coloredwith a 2.25 white canvas, open at both ends, sleeve sewn to the vertical sleeve is available upon request. side of the flag and a 1.25 white canvas sleeve, open at both ends, sewn 362 on top of the flag.32 sleeve, ePoly- 32x0.5 economy polyester sleeve, closed on top.This finishing is for antenna flags.The flag sits at the top of the sleeve. 2" sleeve open at both ends on top & left- Finishing for all deluxe tower poles.The flag is finished with a 2 white canvas sleeve (open at Sleeve for handle bar flag- 0.5 sleeve, open at both ends. The sleeveboth ends) on the top and the left side.is made from the same material as the flag and is white by default.A colored sleeve is available upon request.Sleeve for magnetic pole- 0.4 sleeve, open at both ends. The sleeve is made from the same material as the flag and is white by default.A colored sleeve is available upon request.'